a-52 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com a pu shbu tt on 8060 series alternate action and momentary pushbutton switches features/benefits ? long travel ? available with led ? long life contact design ? epoxy terminial seal compatabile with bottom wash cleaning ? rohs compliant models available typical applications ? instrumentation ? computers and peripherals ? telecommunications and networking equipment specifications contact rating: q contact material: 6 amps @ 120 v ac or 28 v dc; 3 amps @ 250 v ac. see page a-59 for additional ratings. electrical life: 50,000 make-and-break cycles at full load. contact resistance: below 20 m typ. initial @ 2-4 v dc, 100 ma, for both silver and gold plated contacts. insulation resistance: 10 9 min. dielectric strength: 1,000 v rms min. @ sea level. operating temperature: C0?oto 65? solderability: per mil-std-202f method 208d, or eia rs-186e method 9 (1 hour steam aging). cap installation force: 10 lbs. maximum permissible. note: any models supplied with p , r, s, q, b or g contact material are rohs compliant. note: specifications and materials listed above ar e for switches with standar d options. for information on specific and custom switches, consult customer service center. materials case: glass filled nylon 6/6 or diallyl phthalate (dap), flame retardant (ul 94v-0). plunger: s, s1, s2 options: glass filled nylon or glass filled polyester (pbt) (ul 94v-0). l, l1 options: brass, nickel plated. cap & frame: nylon, black standard. bushing: brass or zinc, nickel plated.housing: stainless steel. switch support: brass or steel, matte-tin plated. end contacts: q contact material: coin silver, silver plated. see page a-59 for additional contact materials. center contact & all terminals: q contact material: copper alloy , silver plated. see page a-59 for additional contact materials. terminal seal: epoxy. refer to soldering and cleaning in t echnical data chapter. hardw are: nut & locking ring: brass, nickel plated; lockwasher: steel, nickel plated. build-a-switch to order, simply select desired option from each category and place in the appropriate box. available options are shown and described on pages a-53 thru a-61. for additional options not shown in catalog, consult customer service center. all models have epoxy terminal seal and ar e compatible with all ottom--ash?cb cleaning methods. switch function 8161 spdt on-on 8168 spdt on-mom. 8261 dpdt on-on actuator or plunger s . 710" high plunger with .375" dia. cap j80 snap-in j81 snap-in with frame j82 snap-in with frame for led j86 snap-in with frame & led l .740" high plunger with .395" dia. cap l1 .740" high plunger with .590" dia. cap s1 .615" high plunger with .200" dia. cap s2 .710" high plunger with .310" dia. cap bushing h .300" high, flat, hi torque h9 .300" high, flat, hi torque none no bushing choice required y3 7.6mm, keyway contact material b gold p gold, matte-tin q silver s silver , ma tte-tin g gold over silver r gold over silver, matte-tin seal e epoxy i epoxy potted base cap color 2 black 1 white 3 red 4 orange 5 y ello w 9 gray frame color 2 black led color 3 red none models without led models a vailable terminations a right angle, pc thru-hole av2 vertical right angle, pc thru-hole c pc thru-hole z solder lug a3 right angle, snap-in, pc thru-hole av3 vertical right angle, snap-in, pc thru-hole v3 .460" high, v-bracket v4 .630" high, v-bracket v6 .460" high, v-bracket v21 .555" high, snap-in v-bracket v31 .460" high, snap-in v-bracket w .750" long, wire wrap z3 quick connect
a-53 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com pu shbu tt on a third angle projection 8060 series alternate action and momentary pushbutton switches switch function * panel mounting * panel mounting * panel mounting actua tornap--n front mount dpdt 2-1,5-4 2-3,5-6 on on 8261 dp spdt 2-1 2-1 2-3 2-3 on mom. on on 8161 8168 sp schematic connected terminals pos. 1 pos. 2 switch function pos. 1 pos. 2 model no. no. poles spdt dpdt terminal nos. for refer ence only t erminal nos. for refer ence only part number shown: 8161shzqe part number shown: 8261shzqe mom. = momentary cap finish: matte. other colors available, consult customer service center . a vailable with c, w, z or z3 terminations. note: caps & frames available separately , see pages a-60 and a-61. *incr ease this dimension to .620/.625 (15,75/15,88)for .091/.125 (2,41/2,18) thick panels. *increase this dimension to .620/.625 (15,75/15,88)for .091/.125 (2,41/2,18) thick panels. all models with all options when ordered with g or q contact material. c&k marking this side c&k marking this side 2 black 1 white 3 red 4 orange 5 yellow 9 gray cap color option code j80 snap-in j81 snap-in with black frame actua tor or plunger cap color
a-54 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com a pu shbu tt on third angle projection 8060 series alternate action and momentary pushbutton switches actuatornap--n front mount actuatornap--n front mount * panel mounting * increase this dimension to .620/.625 (1 5,75/1 5,88) for .091/.12 5 (2 ,31/3,18) thick panels. 8161j86zqe223 spdt led not included. for led information, see page a-61. note: caps & frames available separately, see pages a-60 and a-61. other colors available, consult customer service center. 2 black 1 white 3 red 4 orange 5 yellow 9 gray cap color option code 3 red led color option code 2 black 1 white 3 red 4 orange 5 yellow 9 gra y cap color option code available with c, w, z or z3 terminations. note: caps & frames available separately , see pages a-60 and a-61. other colors available, consult customer service center. available with c, w, z or z3 terminations and spdt models only. for led information, see page a-61. actua tor or plunger cap color actua tor or plunger cap color led color j86 snap-in with black frame and led j82 snap-in with black frame for led
a-55 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com pu shbu tt on a third angle projection 8060 series alternate action and momentary pushbutton switches plunger 1/4 40 uns-2a none no bushing choice required (jxx actua tors) y3 7.6mm threaded, keyw a y h9 .300" high unthreaded, flat h .300" high threaded, fla t l1 plunger with cap p/n 8940 l plunger with cap p/n 8941 s2 plunger with cap p/n 8018 s1 plunger with cap p/n 7089 s plunger with cap p/n 7527 2 black 1 white 3 red 4 orange 5 yellow 9 gray cap color option code note: when selecting plunger and cap option, bushing selection must also be made, see below. withstands 12 in./lbs. of torque with no distortion. h bushing standar d with c, w , z or z3 terminations. h9 bushing standard with a, a3, av2, av3, or v3-v31 terminations. withstands 12 in./lbs. of tor que with no distortion. cap finish: gloss. cap supplied not installed. other colors available, consult customer service center. note. t wo mounting nuts, locking ring and lockwasher supplied standar d with thr eaded bushings. optional mounting nut and locking ring styles and finishes available, see section echnical data and additional har dware note: when selecting bushing option, plunger selection must also be made, see above. no bushing option choice required when any jxx actuator option is selected. actua tor or plunger cap color bushing
a-56 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com a pu shbu tt on 8060 series alternate action and momentary pushbutton switches terminations sec t ion a-a .130 (3,3) .138 (3,51 ) pc mounting pc mo unting .750 (19,05) a right angle, pc thru- hole a3 right angle, snap-in, pc thru-hole w wire wrap c pc thru-hole z3 quick connect z solder lug spdt and dpdt spdt and dpdt spdt and dpdt spdt and dpdt 8161sh9abe2 spdt not available with p, s or r contact material. mating quick connector available; order part number 530100000, page a-61. not available with p, s or r contact material. not available with i seal. terminal bend radii and lead-in manufacturing option. note: pc pattern must clear switch support leg. third angle projection
a-57 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com pu shbu tt on a third angle projection 8060 series alternate action and momentary pushbutton switches terminations pc mounting section a-a pc mounting av2 vertical right angle, pc thru-hole, .150" pitch av3 vertical right angle, snap-in, pc thru-hole, .150" pitch a right angle, pc thru-hole 8161sh9a v2be2 spdt 8261sh9abe2 dpdt a3 right angle, snap-in, pc thru-hole not available with i seal. t erminal bend radii and lead-in manufacturing option. not available with i seal. t erminal bend radii and lead-in manufacturing option.
a-58 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com a pu shbu tt on third angle projection 8060 series alternate action and momentary pushbutton switches terminations section a-a pc mounting pc mounting pc mounting not available with i seal. not available with i seal. not available with i seal. t erminal bend radii and lead-in manufacturing option. v21 ver tical mount, v-bracket, snap-in v6 vertical mount, v-bracket v21 ver tical mount , v -bracket , snap-in v6 vertical mount, v-bracket av3 vertical right angle, snap-in, pc thru-hole, .150" pitch av2 ver tical right angle, pc thru-hole, .150" pitch v21 .555 (14,10) v6 .460 (11,68) dim option code v21 .555 (14,10) v6 .460 (11,68) dim option code 8261sh9av2be2 dpdt 8161sh9__be2 spdt 8261sh9__be2 dpdt
terminations a-59 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com pu shbu tt on a third angle projection 8060 series alternate action and momentary pushbutton switches contact material snap-in pc mounting pc mounting v31 vertical mount, v-bracket, snap-in v3, v4 vertical mount, v-bracket v31 vertical mount, v-bracket, snap-in v3, v4 ver tical mount, v-bracket not available with i seal. not available with i seal. 8161sh9__be2 spdt 8261sh9__be2 dpdt v3, v31 .460 (11,68) v4 .630 (16,00) dim option code v3, v31 .460 (11,68) v4 .630 (16,00) dim option code 1 contacts & terminals: copper alloy, with gold plate over nickel plate. 2 end contacts: coin silver, with gold plate over nickel plate. 3 center cont acts & all terminals: copper alloy , with gold plate over nickel plate. 4 end contacts: coin silver, silver plated. 5 center cont act & all terminals: copper alloy , silver plated. 6 terminals: copper alloy , with matte-tin over nickel plate. note: any models supplied with p, s, r,q, b or g contact material are rohs compliant. all models with all options when ordered with s, r, g, or q contact material. b contact material standard with all terminations except c, z & z3. q contact material standard with c, z & z3 terminations. p, s & r contact materials not available with z & z3 terminations. option code cont act ma terial terminal pla ting ra tings silver 5 matte-tin 6 gold 1 silver 4,5 gold over sil ver 2,3 gold 3 matte-tin 6 gold 1 matte-tin 6 low level/dry circuit power low level/dr y circuit or power 0.4 va max. @ 20 v ac or dc max. 6 amps @ 120 v ac or 28 v dc; 3 amps @ 250 v ac. 0.4 v a max @ 20 v ac or dc max. or 6 amps @ 120 v ac or 28 v dc; 3 amps @ 250 v ac. b p q s g r * note: see technical data section of this catalog for rohs compliant and compatible definitions and specifications.
a-60 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com a pu shbu tt on third angle projection 8060 series alternate action and momentary pushbutton switches seal available hardware .200 dia. (5,08 ) .120 (3,05) .155 (3,94) i epoxy potted base e epoxy seal note: a vailable with c, w, z, z3 terminations only. cap part no. 708901000 white 708902000 black 708903000 red 708904000 orange 708905000 yellow 708909000 gra y material: nylon finish: gloss cap part no. 752701000 white 752702000 black 752703000 red 752704000 orange 752705000 yellow 752709000 gra y material: nylon finish: gloss cap part no. 801801000 white 801802000 black 801803000 red 801804000 orange 801805000 yellow 801809000 gra y material: nylon finish: gloss cap, snap-fitting plunger part no. 894001000 white 894002000 black 894003000 red 894004000 orange 894005000 yellow 894009000 gray material: nylon finish: gloss cap, snap-fitting plunger part no. 894101000 white 894102000 black 894103000 red 894104000 orange 894105000 yellow 894109000 gray material: nylon finish: gloss cap, j80, j81 & j82 options only part no. 484601000 white 484602000 black 484603000 red 484604000 orange 484605000 yellow 484609000 gray material: nylon finish: gloss frame part no. 613302263 black material: nylon finish: matte frame part no. 615602263 black material: nylon finish: matte cap, j86 & j96 options only part no. 459701000 459702000459703000 459704000459705000 459709000 material: nylon finish: gloss part no. 476801000 white 476802000 black 476803000 red 476804000 orange 476805000 yellow 476809000 gray material: nylon finish: matte part no. 798201000 white 798202263 black 798203000 red 798204000 orange 798205000 yellow 798209000 gray material: nylon finish: matte note: additional nuts, locking rings and lockwashers available separately , see section echnical data and additional hardware other cap & frame colors available, consult customer service center.
a-61 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com pu shbu tt on a third angle projection .030 (0,76) .200 dia. (5,08?) .025 sq. typ. (0,63) .750 (19,05) .340 (8,64) .230 dia. (5,84?) flat denotes cathode. suggested led for j82 & j84 options. dimensions for reference only. typical applica tion fits z3 t ermination female connector part no. 530100000 a vailable in loose pieces. above frames (part nos. 432xxxxxx) ar e also available with insert which accepts led for indicator light assembly. order insert separately from frame. blank insert panel (without hole for led) also available. led not included. special colors, custom markings available, consult customer service center. p anel inser t with hole for led part no. 894902000 blank p anel inser t without hole for led part no. 476602000 black .047" (1,19) p anel thk. part no. 432502263 .062" (1,57) p anel thk. part no. 432602263 .090" (2,29) p anel thk. part no. 432702263 .125" (3,18) p anel thk. part no. 432802263 black frames snap into panel opening and are independent from switch mounting. accurate positioning of the pc mounted switch relative to the panel opening is necessary to provide proper clearance between actuator and frame. available in two basic styles and four panel thicknesses .047-.125 in. material: nylon. finish: matte. led information switches with led supplied: j86 option: rectangular leds are supplied on 8060 series pushbutton switches with j86 option. these leds are factory installed and are not replaceable. the following specifications apply: process information: soldering to led leads must be completed within 5 seconds at 500o (260?o maximum. caution: cir cuit elements must limit forwar d current of led to 50ma max. continuous. * extra-bright r ed led available (typ. intensity 4.5 mcd), consult customer service center . leds are not supplied with j82 & j84 options. led snaps into switch frame surrounding actuator and is wired externally. 125 mw 75 mw 125 mw 50 ma 30 ma 50 ma 2.5 v 20 ma 10 ma 20 ma 2.1 v 1.0 mcd 0.5 mcd 4.0 mcd green red* y ellow 6 3 5 max ratings at 25o ambient temperature forward continuous power vol t age for w ard current dissip ation typ. forward current typ. forward voltage typ. intensity color option code panel inserts available hardware 8060 series alternate action and momentary pushbutton switches
|
